On the Internet tab of the AirPort Utility, set the Connect Using setting to PPPoE.Įnter the Username and Password for the internet connection using the details that the ISP have supplied. It should show the current Connect Using setting as Ethernet and it will have an IP address in the 192.168.2.x range to indicate that it has received a local IP from the Vigor 130 modem: ![]() ![]() Go to the Internet tab to configure that connection. That will go into the settings for the router and it should show an orange status light / symbol to indicate that it has no internet access. Select the router and click the Edit or Manual Setup button depending on the version of the AirPort Utility that you are using. To configure the Apple AirPort, open the AirPort Utility and the router should show in the list of detected devices. It is recommended to leave the modem unplugged from the AirPort router until the settings have been changed using the AirPort utility. Once the AirPort router has finished updating, the status LED on the AirPort router should light in green to indicate that it has established an internet connection: To do this, connect the Vigor 130's ethernet port to the AirPort router's WAN (circular icon) port. Step 8: Connect the Vigor 130 modem to the AirPort router now. The AirPort router will show as Updating in the utility while it applies the changes. Step 7 : The utility will then pop-up a warning that the AirPort router will be unavailable while applying the changes, click Continue: On the Internet tab, set the Connect Using method to PPPoE and enter the ISP Username in the Account Name then enter the Password for that account.ĭo not enter a Service Name, it is not required for this connection type: ![]() Step 5: The AirPort router should now show as a configurable device, click on the icon of the router and click Edit: Step 4: Do not connect the modem to the router at this stage, simply click Next: Step 3: That will go into the initial setup for the AirPort router, set the name, enter a suitable password for the router and click Next: Otherwise, the router should show in the list of detected devices under the Other Wi-Fi Devices menu: If the router is already detected, skip to Step 5. Step 2: To configure the Apple AirPort, open the AirPort Utility from Finder > Utilities. Step 1: Connect the Vigor 130 modem to the VDSL2 line using the DSL port, the DSL LED will be lit solidly when the VDSL2 connection has established.ĭo not connect its ethernet port to the Apple AirPort router at this stage. Connect the RJ-45 Ethernet port on the Vigor 130 to the WAN ethernet port of your Apple AirPort router. ![]() Configure the WAN interface on your router to use PPPoE and enter the username and password details for the internet connection.Connect the RJ-11 port (marked 'DSL') on the Vigor 130 to the VDSL or ADSL line.ADSL VPI/VCI is set to 0/38 for PPPoA connections, 0/101 for MPoA connections.Configured to pass through a PPPoE connection.The computer will need to be plugged into the modem's Ethernet port to access this interface. This can be used to check ADSL / VDSL diagnostic information or re-configure the modem to bridge a DHCP / Static IP connection if required. The DrayTek Vigor 130 modem has a web interface available on (username of "admin" and password of "admin" by default). The settings on the Vigor 130 are correct for most UK lines out of the box, so in most cases it should only be necessary to configure the router that it is connected to. The Vigor 130 does not store any Internet usernames or passwords itself - those go into your router's configuration instead. The Vigor 130 is a pre-configured VDSL2 / ADSL2+ modem that takes a VDSL2 or ADSL2+ connection and performs full pass-through / bridge to Ethernet presentation, which can then be used by a device such as a router to connect directly to the internet.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |